New products
-
Creasol DomBus33 - Smart light controller, with 3 relay outputs, 3 AC inputs, 5 I/Os
-
Creasol DomBus37: DIN rail domotic module with 12 analog/digital inputs, 3 AC inputs and 3 relay outputs for building automations
-
Creasol DomBusEVSE: smart electric vehicle charging controller for DIY wallbox
-
Creasol DomBus12: compact module for home automation system, with 9 configurable I/O
-
Creasol DomESP1 and DomESP2: Input/output/supply board for ESP8266 module
-
Creasol DomBus1: Domoticz board with 2 relays, 6 inputs, 1 AC input
-
Creasol DomBus34 - Din rail module supporting up to 4 energy meters, 2 relay outputs, 1 AC input, 2 inputs
-
Creasol DomBus36 - 12 relays DIN-rail module with very low power consumption - DomBus and Modbus protocols
Latest news
- Complete burglar alarm system with Domoticz
- Measure the consumed/produced energy with Domoticz
- Installing ESPEasy firmware on NodeMCU v3 board, and configuring it to be used with Domoticz
- FAQ veicoli elettrici e fotovoltaico
- Photovoltaic and renewable energy
- Domoticz: extracting a field from a multi-value sensor
- Controlling heat pump to optimize power consumption from photovoltaic
- Plug and Play Home Automation kits with Domoticz
- How to build a domotic system using DomBus modules
- Node-RED and Creasol DomBus modules
- Antenna 433 MHz, standard version
- Antenna 433 MHz, filtered version

- Details
- Category: Remote controls
Duplicates several types of remote control for gates, garage doors, barriers, which transmit a fixed code in the frequency 433.92 MHz with OOK/ASK modulation. Each button is independent, so it's possible to clone up to 4 different remote controls, even if made by different manufacturers.

- Details
- Category: Remote controls
Light-weight (only 16g), soft-touch cover and long range remote control duplicator 433.92MHz.

- Details
- Category: Remote controls
This device is able to duplicate several types of remote control for gates, garage doors, barriers, which transmit in frequencies between 286 and 868 MHz. Each button is independent, so it's possible to clone up to 4 different remote controls, even if they operates in different frequencies.

- Details
- Category: Remote controls
Like Creasol Multi, same firmware and price, but light-weight (only 16g), soft-touch cover, transmits at 433 MHz and 868 MHz.

- Details
- Category: Remote controls
Small remote control duplicator, only 41x31x11mm, copy up to 4 different remote controls which transmit a fixed code in one of the supported frequencies, listed in the Tab.1,

- Details
- Category: Remote controls
Compact transmitter, 41x31x11mm, can be connected to 1-4 external switches so, when a switch is pressed or released, it starts transmitting.

- Details
- Category: Universal receivers
Small device, 41x31x11mm, that can be used to open a main door or pedestrian door (with electric lock) using almost any radio remote control in the market which transmits in a frequency between 220 MHz and 868 MHz, AM and FM, fixed and rolling code.

- Details
- Category: Universal receivers
Small universal remote control duplicator, only 41x31x11mm, can be used with almost any radio remote control in the market which transmit in a frequency between 288 MHz and 868 MHz, AM and FM, fixed and rolling codes.

- Details
- Category: Universal receivers
Multi-frequency universal receiver has 2 optoisolated outputs, with 60V and 30-100mA capability, and can be supplied from 8Vdc to 36Vdc, and from 10Vac to 27Vac.

- Details
- Category: Universal receivers
Multi-frequency universal receiver has 2 relay outputs, with 250V and 5A capability, and can be supplied from 9Vdc to 36Vdc, and from 10Vac to 27Vac.

- Details
- Category: Antennas
2.1dBi gain, 50Ω impedance, 433-435 MHz band, 10W max. Antenna has LC filter to reduce noise outside 433-435MHz band (narrow bandwidth)

- Details
- Category: Antennas
2.1dBi gain, 50Ω impedance, 425-440 MHz band, 10W max

- Details
- Category: Antennas
2.1dBi gain, 50Ω impedance, 860-880 MHz band, 10W max
- Details
- Category: Batteries
CR2032, 3V LiMnO2 cell, 20mAh, high quality, bulk packing 50pcs/carton
Can be sold with Ecotax already included only for italian customers
Capacity: 20mAh
Dimensions: length 28.5mm, diameter 8mm
- Details
- Category: Batteries
CR2032, 3V LiMnO2 cell, 210mAh, blister packing 5pcs/blister, 100pcs/carton
Can be sold with Ecotax already included only for italian customers
Capacity: 210mAh
Dimensions: diameter 20mm, height 3.2mm
- Details
- Category: Batteries
CR2032, 3V LiMnO2 cell, 240mAh, very high quality, bulk packing, 40pcs/tray, 480pcs/pack, 4800pcs/carton
Can be sold with Ecotax already included only for italian customers
Capacity: 240mAh
Dimensions: diameter 20mm, height 3.2mm

- Details
- Category: Home automation
DomBus1 is the first domotic module of DomBus serie, integrating 6 inputs, 2 relay outputs, 1 AC input.

- Details
- Category: Home automation
Creasol DomBus12 is a compact module, 40x30x11mm, with 9 configurable inputs/outputs.
It can be connected to the Domoticz controller by a RS485 serial bus (4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps).
As other DomBus devices, DomBus12 is designed to consume low power, be reliable, fully configurable and easy to use. Each port is fully configurable, e.g. as analog or digital input, twinbutton (double button), counter, buzzer, NTC 10k, ... 2 ports may be used as open-drain output, to activate 2 external relays or LEDs.

- Details
- Category: Home automation
Creasol DomBus23 is a module for home automation system with several different kind of configurable inputs/outputs in a short size: 74x72x24mm.

- Details
- Category: Home automation
AVAILABLE IN TWO VERSIONS: DomBus protocol and Modbus protocol!
Creasol DomBus31 is a din-rail relay module, 115x90x40mm, with 8 relays outputs. 6 relays are SPST (Normally Open outputs) with 250V 5A max capability, and 2 relays are SPDT (both Normally Open and Normally Closed outputs) with 10A capability. High efficiency module, with very low power consumption, only 600mW with all relays ON.

- Details
- Category: Home automation
DomBus32 is a DIN-RAIL module, 54mm wide, with 3 relay outputs, 3 AC inputs and 5 low-voltage I/Os.
AVAILABLE IN TWO VERSIONS: DomBus protocol and Modbus protocol!
- Details
- Category: Home automation
DomBus33 is a DIN-RAIL module, 54mm wide, designed to control an existing lighting system with 3 lights using 115/230V pushbuttons and step-by-step relays.
DomBus33 has 3 relay outputs, that can be used to send pulses to existing step-by-step relay coils to switch lights ON/OFF, 3 AC inputs to be connected to the step-by-step relay contact to know the ON/OFF light status, and 5 low-voltage I/Os that can be connected to additional pushbuttons and/or switches to activate/deactivate single lights, or activate/deactivate all lights (useful to turn all lights OFF when leaving home).
In this way lights can be controlled by both existing pushbuttons and domotic controller (smartphone, web interface, automation, scenes, groups).
To simplify wiring, the terminal block has 3 terminals for relays, 3 for AC inputs, and 1 terminal for the common (usually Neutral, but Line can be used as well): in this way it's easier and faster to connect the module to the light system. Please take care to connect only loads that are protected by the same RCCB (circuit breaker).
As other DomBus modules, all ports can be configured in many different ways, and also this module supports DCMD, commands sent to the same or other modules to perform simple actions, that permit to achieve high reliability (DCMD commands work even if domotic controller is not operational) and easy programming (don't need to create automations in the domotic controller, just configure DomBus ports to perform actions on events). Last, but not least, as other DomBus modules it's optimized to get low power consumption, less than 10mW normally (0.75mA @13.6V) and less than 150mW when all relays are ON (10mA @13.6V).
Features
- 3 relay outputs, 250Vac 5A max, with overvoltage protection (varistors)
- 3 AC inputs, 110-230V, to monitor voltage on loads
- 1 common (Neutral or Line) for both relays and AC inputs, to simplify connections
- 5 programmable I/Os
- 8-25Vdc power supply
- 10mW power consumption
- 150mW max power consumption
- 52x89x65mm
Application notes

- Details
- Category: Home automation
DomBus34 is a DIN-RAIL module, 54mm wide, designed to interface up to 4 power/energy meters, type DDS 238-2 ZN/S (Modbus), to measure power and energy (both imported and exported), voltage frequency and power factor.

- Details
- Category: Home automation
Creasol DomBus36 is a din-rail relay industrial-grade module for building automations and home automation systems, 115x90x40mm, with 12 relays outputs, SPST (Normally Open outputs) with 250V 5A max capability, divided in 3 groups of 4 relays, each group with a 5-position screw terminal blocks: 1 common + 4 outputs

- Details
- Category: Home automation
Domotic module, 115x90x40mm, supporting both DomBus and Modbus RTU protocols, that integrates 12x low voltage analog/digital inputs, 3x relays outputs, 3x 115Vac / 230Vac inputs. Optionally it is able to control and monitor the power supply fed to a burglar alarm external siren.
Suitable to interface alarm sensors (magnetic contact sensors, PIRs, tampers), monitor power outage (by the 3 AC inputs) and control up to 3 outputs (relays).

- Details
- Category: Home automation
Creasol DomBusEVSE is a fully tested DIN rail module, designed for Domoticz home automation system, to charge electric vehicles using the standard IEC 62196-2 Mode3 (AC charge, up to 22kW power).
It works as stand-alone (without any domotic controller) or in managed mode (charging current controlled by Domoticz).

- Details
- Category: Home automation
Creasol DomBusTH is a fully configurable small electronic board, 32x17mm, that can fit any blank cover with a 3.5mm hole in the centre, needed by the thermal/humidity sensor to exchange air with the room and to get the 3 LEDs light out. It can be connected to the Domoticz controller by a RS485 serial bus (using a standard alarm cable with 4 wires, 2 for 12/24V power supply, and 2 for data at 115200bps). Available in both DomBus and Modbus protocols

- Details
- Category: Home automation
ESP8266 is a very powerful and cheap MCU equipped with WiFi transceiver, very useful to expand inputs/outputs of a Raspberry/Domoticz controller.
Creasol DomESP1 board is designed for ESP8266 module NodeMCU V3, with 900 mils header pitch (optionally, soldering additional headers, it's possible to use the 1100mils module or WeMos D1 mini module), and integrates the whole circuitry to manage digital inputs, one analog input, 4 relay outputs, 1 low voltage output, I2C bus, 1wire bus and 2 mosfet outputs with 12A 30Vmax capability.

- Details
- Category: Home automation
Creasol DomRelay2 is a compact module, 43x24x25mm, within 2 relays with 12V 200mW coil, 250V 5A SPST contact with special material designed to prevent contact welding due to excessively high surge current load (capacitive loads or tungsten lamps).
Contacts are protected from overvoltage by metal oxide varistors; coils are protected from overvoltage by free-wheeling diodes.
Relay coil should be driven at 12Vdc 17mA: using DomBusTH or DomBus12 modules it's possible to drive relays using a lower power system, consuming less than 1/4 of nominal power.