Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
 

After duplication, how many times the RED LED flashes?
  1. 2 times: the original remote control transmits a fixed code that, most probably, has been duplicated successfully
  2. 4 times: the original remote control tranmits a rolling code, that most probably can NOT be copied
  3. 8 times: the battery voltage is too much low, and for security reasons the remote control do NOT save the information into its memory: change the battery on the duplicator and repeat programming.


What is the frequency of the original remote control?
  1. between 26 MHz and 40 MHz: cannot be duplicated by our devices
  2. between 286 and 418 MHz: most probably it can be duplicated by Creasol Multi and MultiST: check later
  3. 433.92 MHz: may be duplicated by Creasol Multi, MultiST and Four: check later
  4. 868.3 or 868.35 MHz: may be duplicated by Creasol Multi and MultiST : check later



If the transmission frequency of the original remote control is one of the frequency listed in the table, it's possible to try the following procedure that let MULTI receiving only at the specified frequency, instead of scanning all the supported frequencies:
  1. Press together buttons 1+2, until LED becomes solid green
  2. Release all buttons
  3. Press N times the button where you wish to duplicate the original code, where N correspond with the desired frequency (see table): every time you press the button, RED led lights to help you counting N times
  4. Then, the remote control starts to receive exactly in the selected frequency: press the button on the original transmitter to copy  the transmitted code on Multi or MultiST.

 

Multi does not work. Pressing any button, LEDs do not light
Maybe the battery is flat: open the remote control case (using a screwdriver), then remove the battery, press any button, insert a new battery.
Press again one button to check that LED red flashes (remote control transmits)

Pressing any button, LED starts RED and becomes steady-GREEN shortly
While pressing a button to transmit, if the LED become steady GREEN, it means that battery is flat and must be replaced

Pressing any button, LED blinks RED and GREEN alternatively
This mean that battery is almost flat. Please note that battery status depends by temperature, so at higher temperatures battery works much better. Also, sometimes the remote control does not transmit at all, but pushing the button again it starts transmitting correctly: this is an algorithm intended to notify the user about the status of battery, so when you see that sometimes the remote control does not transmit, look at the LEDs to see the status of battery!

Pressing the button, RED LED flashes correctly, but it does not activate the automation (gate, garage door, ...)
Try from a shorter distance from the receiver. Consider that normally MULTI performs lower range than original remote controls, because it is not optimized for a single frequency. Try with the original remote control, to check that the receiver works correctly. Try to duplicate another time the original remote control on MULTI: maybe that someone has programmed another code on that button


FRANCAISE
Multi ne fonctionne pas. Appuyant sur un bouton, les LED ne s'allume pas
Peut-être que la batterie est vide: ouvrir le boîtier de télécommande (en utilisant un tournevis), puis retirez la batterie, appuyez sur un bouton, insérez une nouvelle batterie.


Appuyant sur un bouton, la LED commence ROUGE et devient stable peu VERT
Tout en appuyant sur un bouton pour transmettre, si la LED verte régulière devenir, cela signifie que la batterie est à plat et doit être remplacé


Appuyant sur un bouton, la LED clignote en rouge et vert alternativement
Cela signifie que la batterie est assez plat. S'il vous plaît noter que le statut de la batterie dépend de la température, donc essayer de la télécommande à des températures élevées ça marchera mieux. Dans ces conditions, il arrive que parfois la télécommande ne transmet rien, et parfois il transmet correctement: il s'agit d'un algorithme destiné à avertir l'utilisateur sur l'état de la batterie, alors quand tu vois que parfois la télécommande ne transmet pas, regarder les LED pour voir l'état de la batterie!


En appuyant sur le bouton, LED rouge clignote correctement, mais il n'active pas l'automatisation (portail, porte de garage, ...)
Essayez d'une plus courte distance du récepteur. Considérez que normalement MULTI effectue bas de la fourchette de télécommandes d'origine, car il n'est pas optimisé pour une seule fréquence. Essayez-le avec la télécommande d'origine, afin de vérifier que le récepteur fonctionne correctement. Essayez de reproduire une autre fois la télécommande d'origine sur le MULTI: peut-être que quelqu'un a programmé un autre code sur ce bouton



ITALIANO
MULTI non funziona. Premendo un qualsiasi pulsante, i LED non si accendono
Forse la batteria è scarica: aprire la scatola (utilizzando un cacciavite), quindi rimuovere la batteria, premere un pulsante, inserire una nuova batteria

Premendo un tasto qualsiasi, LED lampeggia inizialmeno ROSSO per poi diventare VERDE fisso
Tenendo premuto un pulsante per trasmettere, se il LED verde si ferma, significa che la batteria è scarica e deve essere sostituito


Premendo qualsiasi tasto, il LED lampeggia ROSSO e VERDE alternativamente
Questo significa che la batteria è quasi scarica. Lo stato della batteria dipende dalla temperatura, e funziona meglio a temperature alte. In questo caso, potrete notare che a volte il radiocomando non trasmetterà nulla, ed a volte trasmetterà correttamente, grazie ad un algoritmo utilizzato per informare l'utente circa lo stato della batteria: quando noterete questo malfunzionamento, controllate i LED per verificare lo stato della batteria!


Premendo il pulsante, LED ROSSO lampeggia correttamente, ma non attiva l'automazione (cancello, porta del garage, ...)
Provate da una distanza inferiore dal ricevitore. Si consideri che normalmente MULTI ha una portata minore rispetto ai radiocomandi originali, perché non è ottimizzato per una singola frequenza. Provate con il telecomando originale, per verificare che il ricevitore funzioni correttamente. Provate a duplicare nuovamento il radiocomando originale sul MULTI: forse qualcuno ha programmato un altro codice su quel pulsante
 
Pin It