User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

IntroductionCreasol SenderBatt - Blackout monitor and transmitter/duplicator (convert external switch/button into transmitters)

This compact transmitter, 41x31x11mm, can be connected to 1-4 external switches so, when a switch is pressed or released, it starts transmitting. It's supplied pre-programmed with 4 random codes, but it's also possible to copy up to 4 remote controls which transmit a fixed code in the supported frequencies, listed in the Tab.1.

Channels 1 and 2 can be programmed to be activated when switch gets closed, open or in both cases, while channels 3 and 4 works only in normally open mode (transmit when the corresponding switch gets closed). Also, device can transmit a different code when the switch get closed and open. See below.

The transmission frequency, power (from 10uW to 10mW), length (max number of telegrams that should be transmitted) and other parameters, can be simply configured, for any channel, using the Prog button: any channel is indipendent from the other, so it's possible, for example, to have one channel programmed to transmit at 433.92MHz, another one for 868.3 MHz, and so on.

Configuring for each channel the appropriate transmission power, it is possible to minimize interferences and collisions, or maximize the distance: it has a very long range when the maximum transmission power is selected.

Switch #1 gets closed => Transmit code #1 if Par.9 = 1 or 3
Switch #2 gets closed => Transmit code #2 if Par.9 = 1 or 3
Switch #3 gets closed => Transmit code #3
Switch #4 gets closed => Transmit code #4
Swtich #1 gets open => Transmit code #5 if Par.9 = 2 or 3
Swtich #2 gets open => Transmit code #6 if Par.9 = 2 or 3

For example, if channel 1 is programmed with Par.9=3, it transmits code #1 when switch #1 gets closed, and transmits code #5 when switch #1 gets open. This can be used, for example to notify the status of window or door: when window gets open, stop air conditioning; when window gets closed, start air conditioning system.

List of supported frequencies

Can also be used to open a gate, garage door or traffic barrier, as like as other home automations (domotic appliances), by pressing one or more button switches.

It's supplied by the internal CR2032 3V battery, but it's possible to externally connect 2 AA NiMH or alkaline batteries to get an extended lifetime.


 

Connection diagram from Creasol SenderBatt transmitter / power failure monitor


It's supplied in nice transparent recyclable clamshell with instructions printed in 2 or more languages. Companies that would like to distribute this product can send an inquiry to This email address is being protected from spambots. You need JavaScript enabled to view it. specifying the company details, including VAT ID. We can also supply this device with instructions customized with your customer logo, name, details and preferred languages.

Documentation

creasolMultiFourRecLock


Application note SENDERBATT_01: 4 channels remote control transmitter / duplicator

application pdfDownload this application note in PDF format

 

AN senderBatt 01


Pin It
Creasol SenderBatt - 4 channels transmitter/duplicator
SKU creSenderBatt
Brand Creasol

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

IntroductionCreasol Sender Long range remote control duplicator and transmitter

This small remote control duplicator, only 41x31x11mm, is able to copy from 1 to 4 original remote controls which transmit a fixed code in one of the supported frequencies, listed in the Tab.1.

The frequency, transmission power and other parameters, can be simply programmed using the Prog button. Also, Prog button can be pressed without the need to open the case.

Changing the transmission power is possible to minimize the interference and collisions or maximize the distance.

It can be used open a gate, garage doors or traffic barrier, and it's suitable to be connected to a domotic controller to transmit a code when it's supplied.

It can be connected, through a switch, to an external power supply: a wide range of voltage, 7÷35Vdc and 5÷24Vac, is supported.
When the switch is pressed/closed, the device is supplied and starts to transmit the code that was previously learned.

Also, programming CreasolSender in mode2 or mode3, it's possible to push the power supply switch more times to select the code that should be transmitted, as shown in the following figure.

creSender2 diagram

It's supplied in nice transparent-recyclable clamshell with instructions printed in more languages. Companies that would like to purchase this product can send an email to This email address is being protected from spambots. You need JavaScript enabled to view it. specifying the company details, including VAT ID. We can also supply this device with customized instructions.

Crasol Rec1Uni and LockUni: list of supported frequencies

Documentation

  • Creasol Sender video youtube

creasolMultiFourRecLock

 


 

Application note SENDER_01: Externally-supplied remote control duplicator - Some applications

application_note_sender_01

Download this application note in PDF format

Italiano

Questa nota applicativa mostra alcuni esempi di applicazioni per Creasol Sender, un duplicatore di radiocomandi, che viene alimentato esternamente e iniziare a trasmettere non appena l'alimentazione viene applicata. Può essere utilizzato come un normale telecomando, per aprire cancelli o porte di garage o barriere, all'interno di un'automobile o applicato ad un pulsante di casa. Inoltre può essere utilizzato per trasmettere un codice ad un controller domotico o altro ricevitore, per notificare un evento ed eseguire alcune azioni.

English

This application note shows some example of applications for Creasol Sender, a remote control duplicator which is supplied by external power supply and start to transmit as soon as power supply is applied. It can be used as a normal remote control, to open gates or garage doors or traffic barriers, inside a car or applied to a pushbutton switch in the house. Also it can be used to transmit a code to a domotic controller or another receiver, to notify an event and perform some actions.

Français

Cette note d'application montre quelques exemples d'applications pour Creasol Sender, un duplicateur de télécommande qui est fournie par une alimentation externe et commencer à communiquer dès que l'alimentation est appliquée. Il peut être utilisé en tant que contrôle à distance normale, pour ouvrir des portes ou des portes de garage ou de barrières de circulation, à l'intérieur d'une voiture ou appliqué à un bouton-poussoir dans la maison. Aussi elle peut être utilisée pour transmettre un code à une unité de commande domotique ou d'un autre récepteur, pour notifier un événement et d'effectuer certaines actions.

Deutsch

Diese Application Note zeigt einige Beispiele von Anwendungen für Creasol Sender, eine Fernbedienung Duplizierer, die durch externe Netzteil mit Strom versorgt wird und beginnen, sobald Spannung anliegt übertragen. Es kann als eine normale Fernbedienung verwendet werden, um Tore oder Garagentore oder Traffic Schranken öffnen, in einem Auto oder auf einen Taster im Haus. Auch kann es verwendet werden, um einen Code zu einem domotic Controller oder einen anderen Empfänger zu übertragen, um ein Ereignis zu benachrichtigen und einige Aktionen.

Español

Esta nota de aplicación muestra algunos ejemplos de aplicaciones para Creasol Sender, una duplicadora de control remoto que se suministra con fuente de alimentación externa y empezar a transmitir tan pronto como fuente de alimentación se aplica. Se puede utilizar como un control remoto normal, para abrir puertas o puertas de garaje y barreras de tráfico, dentro de un automóvil o se aplica a un interruptor pulsador en la casa. También se puede utilizar para transmitir un código a un controlador domótico o receptor otro, para notificar un evento y realizar algunas acciones.

Português

Esta nota de aplicação mostra alguns exemplos de aplicações para Creasol Sender, um duplicador de controlo remoto que é fornecido pela fonte de alimentação externa e começar a transmitir logo que fonte de alimentação é aplicada. Ele pode ser usado como um controlo remoto normal, para abrir portas ou portões de garagem ou de barreiras de trânsito, dentro de um carro ou aplicados a um comutador de botão de pressão na casa. Também pode ser utilizada para transmitir um código para um controlador de domótica ou de outro receptor, para notificar um acontecimento e realizar algumas acções.


 

 

 


Pin It
Creasol Sender - Multi-frequency remote control duplicator ext-supplied
SKU creSender
Brand Creasol

User Rating: 4 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Inactive

Creasol MultiST: Duplicate your remote controls easily!!

tab1

creMulST clamshell 200CreMulST - Creasol Multi SoftTouch multi-frequency remote control duplicatorLike Creasol Multi, same firmware and price, but light-weight (only 16g), soft-touch cover and longer range at 433.92MHz (optimized for 433MHz).

This remote control is able to copy several types of remote control for gates, garage doors, traffic barriers, which transmit in frequencies between 286 and 868 MHz (433.92, 868.3, 315, 403.55, 418MHz, and all frequencies between 286 and 390 MHz). Range from 286 to 418MHz is not enable for EU market.

Duplication is very easy: both frequency and code are learned automatically, without the need of external equipment.

Each button is independent, so it's possible to clone up to 4 different remote controls, even if they transmit in different frequencies. For example, you can program CAME TOP432 (433.92 MHz) on button 1, HORMANN HSM4 (868.3) on button 2, LIFTMASTER 63LM (390 MHz) on button 3 and LINEAR Multicode (300 MHz) on button 4.Any supported code and frequency combination is possible. Look at the compatibility table!

The remote control is made in EU, supplied in a nice transparent resealable recyclable clamshell, with instructions printed in several languages, 3V battery already installed, mobile strap, and 2 years warranty.

Available in different colors.
creMulST colors small

Pin It
Creasol MultiST: Universal multi-frequency remote control duplicator with soft-touch casing
SKU creMulST
Brand Creasol

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

Introduction

This device is able to duplicate several types of remote control for gates, garage doors, barriers, which transmit in frequencies between 286 and 868 MHz. Each button is independent, so it's possible to clone up to 4 different remote controls, even if they operates in different frequencies. creMul3_150

Duplication

Duplication is very very easy, and does NOT require any external equipment (frequency counter, programming machine, sniffer):

  1. Press together buttons 1 and 2, until LED becomes green.
  2. Release all buttons.
  3. Press the button where you wish to duplicate the original remote control.
  4. Start to transmit by pressing and holding the button on the original remote control, keeping it at 10cm from this device.

When duplication ends, LED flashes 2 times in case of fixed code, or 4 times in case of rolling code. Then LED becomes green and duplication procedure restart from point 3.

After duplication, each button should be pressed at least 2 times to assure that the gate or garage works correctly.

tab1

Initialization of a 32 bit random code

Follow the instructions below to set a new random code on one or more buttons, even in different frequencies:

  1. Press together buttons 3 and 4, until LED becomes green.
  2. Release all buttons.
  3. Press the button, where you wish to initialize the code, a number of times corresponding to the desired frequency, as indicated in Tab.1.

The remote control emits 2 flashes, then it's possible to initialize a new random code on another button restarting the procedure from point 3.

This feature is useful mainly for 2 reasons:

  • Remove a previously stored code from the remote control, for example after showing to a customer how duplication work.
  • Program a random code that will be used to program a universal receiver, or any receiver that manages the 12bit type code, selecting the desired frequency.

Battery status and replacement

If, during transmission or duplication, both LEDs blink (red and green), the battery voltage is low: in this case the battery should be flat, or the temperature too low. In the first case, the enclosure should be opened loosening the 2 screws, picking up the board and replacing the existing battery with a new CR2032 battery.

Product lookcreMul_blister_150

The remote control duplicators is sold in blister, with printed instructions in 6 languages. It's supplied 100% tested and working, with the battery inside, and both snap hook and key ring.

It's possible to customize the instructions with your preferred languages, brand and model name, even for small quantities.

Other documents

 

 

 

Pin It
Creasol Multi - Universal multi-frequency remote control duplicator
SKU creMul
Brand Creasol

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

IntroductioncreFour3_150

This device is able to duplicate several types of remote control for gates, garage doors, barriers, which transmit in the frequency 433.92 MHz with OOK/ASK modulation. Each button is independent, so it's possible to clone up to 4 different remote controls, even if made by different manufacturers.

Duplication

Duplication is very very easy, and do NOT require any external equipment (frequency counter, programming machine, sniffer):

  1. Press together buttons 1 and 2, until LED becomes green.
  2. Release all buttons.
  3. Press the button where you wish to duplicate the original remote control.
  4. Start to transmit by pressing and holding the button on the original remote control, keeping in touch with the duplicator.

When duplication ends, LED flashes 2 times in case of fixed code, or 4 times in case of rolling code. Then LED becomes green and duplication procedure restart from point 3.

After duplication, each button should be pressed at least 2 times to assure that the gate or garage works correctly.

Initialization of a random 32 bit code

Follow the instructions below to set a new random code on one or more buttons:

  1. Press together buttons 3 and 4, until LED becomes green.
  2. Release all buttons.
  3. Press twice the button where you wish to initialize the code.

The remote control emits 2 flashes, then it's possible to initialize a new random code on another button restarting the procedure from point 3.

This feature is useful mainly for two reasons:

  • Remove a previously stored code from the remote control, for example after showing to a customer how duplication work.
  • Program a random code that will be used to program a universal receiver, or any receiver that manages the 12bit type code.

Battery status and replacement

If, during transmission or duplication, both LEDs blink (red and green), the battery voltage is low: in this case the battery should be flat, or the temperature too low. In the first case, the enclosure should be opened loosening the 2 screws, picking up the board and replacing the existing battery with a new 27A alkaline battery (12V 20mAh).creFour_blister_150

Product look

The remote control duplicators is sold in blister, with printed instructions in many languages. It's supplied 100% tested and working, with the battery inside, and both snap hook and key ring.

Instructions can be customize with the preferred languages, brand and model name, logos, even for small quantities.

Other documents

 

 

 

Pin It
Creasol Four - Universal remote control duplicator 433.92 MHz
SKU creFour
Brand Creasol